Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Don't ignore the forklift at work. If the procedure is bad, there will certainly be serious mishaps in minutes, and there are lots of mishaps entailing forklifts.

Situation 1: The forklift cargo blocked the motorist's view, and the individual in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the path and hangs on the roadside shelf, which almost triggers an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the workers illegally, the forklift driver does not put on the seat belt, the forklift lifter falls and the driver is squashed when the forklift surrender.
Case 7: The forklift vehicle driver did not put on a safety belt and fell from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure prior to beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be increased too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided first. High-speed sharp turns are banned. High-speed doglegs will cause the automobile to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with tons unless there are special conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be effectively slanted back. The lots will not be elevated other than when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is raised, raised or driven, it is restricted for employees to base on the fork to hold items and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special conditions, security indication need to be established to remind bordering pedestrians. .
3. In the process of packing and unloading things, the forklift should be stopped with the brake. .
4. The speed of the vehicle need to be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When utilizing a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at high speed and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the look Stand-on Electric Pallet Stacker must be inspected, and fuel, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak needs to likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline must be sluggish and consistent, and Stand-on Electric Pallet Stacker no switching on the incline is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and go to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an obstacle on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844